- Density, g/cm³
- 1.35 (± 0.05)
- Drying Time, h
- ~24-36
- Packing
- A: 24 kg + B: 8 kg (total 32 kg)
- Consumption, kg/m²
- 3-5 kg
Technical Specifications
| Parameter | Value |
|---|---|
| Density, g/cm³ | 1.35 (± 0.05) |
| Drying Time, h | ~24-36 |
| Packing | A: 24 kg + B: 8 kg (total 32 kg) |
| Consumption, kg/m² | 3-5 kg |
| Elongation, % | 90 |
| Solid Content (Mixing Ratio), % | A/B: liquid/solid: 3/1 |
| Shelf Life, months | 12 |
| Application Equipment | Applied with brush or roller |
Product Description
IZOBITUM 2K is a rubber-bitumen-based, polymer-modified waterproofing product. It is two-component, consisting of a liquid component of bitumen emulsion and a cement-based powder component enriched with chemical additives. It can be used for foundation tanking and curtain (retaining) wall waterproofing of buildings, as well as for waterproofing balconies and terraces. It is applied to mineral-based substrates such as concrete, screed, plaster and mortar.
Application Areas
- In waterproofing of building foundations
- In waterproofing of curtain walls and retaining walls
- In waterproofing of underground car park floors
- In waterproofing of wet areas
- In repairing waterproofing such as old bituminous membranes, pitch, asphalt and tar paper
- Used below and above ground, horizontally and vertically.
Advantages
- Can be applied with a brush or an airless spray gun.
- Does not sag on vertical surfaces.
- Retains its elasticity even at low temperatures.
- Can be applied on all mineral surfaces such as concrete, stone, brick and concrete block.
- Provides jointless, seamless waterproofing against all kinds of water and moisture effects.
- Solvent-free, non-flammable (does not ignite or catch fire).
- Can be applied on dry and slightly damp surfaces.
- Can bridge cracks.
Application
Application is carried out with a brush or suitable spray equipment.
Application of the 1st coat: First, one coat of IZOBITUM 2K is applied (approximately ½ of the consumption) and an 80 g/m² reinforcing mesh is laid onto it wet-on-wet. The layer is left to dry.
Application of the 2nd coat: After the first coat has dried, the second coat of IZOBITUM 2K is applied. The first coat must not be damaged while applying the second coat.
No coating should be applied before the previous coat has completely dried. It should be borne in mind that the drying time may be prolonged in humid and cold environments, and care should be taken to ensure sufficient ventilation to support drying.
Packaging & storage
Packaging
A: 24 kg + B: 8 kg (total 32 kg)
Shelf Life
12 months
Where it is used
Used together with
- PROOF MY · One-Component Polyurethane-Based, Easy-to-Apply, UV-Resistant Liquid Membrane Developed for Waterproofing and Protection
- PUR 560 · Two-Component, 100% Solids Hybrid Polyurea Coating System with Fast-Curing and Flexible Properties
- PUR 670 · Two-Component Flexible 100% Pure Polyurea Spray Coating System
- PUR 770 · Two-Component Hot-Applied Flexible and Economical Polyurea Coating System
- KBE · One-Component Bitumen Emulsion-Based Primer
- PROOF RC 2K · Two-Component Polyurethane-Bitumen-Based Liquid Membrane Developed for Waterproofing and Protection
- KB · One-Component, Bitumen-Rubber-Based, UV-Resistant, Elastic Waterproofing Material
- SB · UV-Resistant Waterproofing Membrane Consisting of Special Mineral Filler and Polymer Components
Documents
Technical data sheet (TDS)
Review the recorded specifications, packaging and storage information.
View technical data sheet ↗Safety & lot documents
Request the current SDS and the certificate of analysis (CoA) for the lot you are evaluating.
SDS available on request.
Request Sample
Product Information
Polymer-Modified, Bitumen-Rubber-Based, Two-Component Waterproofing Material Typical specifications: Density, g/cm³: 1.35 (± 0.05); Drying Time, h: ~24-36; Packing: A: 24 kg + B: 8 kg (total 32 kg). KORKİMYA supplies IZOBITUM 2K in A: 24 kg + B: 8 kg (total 32 kg). Shelf life: 12 months.
IZOBITUM 2K is a rubber-bitumen-based, polymer-modified waterproofing product. It is two-component, consisting of a liquid component of bitumen emulsion and a cement-based powder component enriched with chemical additives. It can be used for foundation tanking and curtain (retaining) wall waterproofing of buildings, as well as for waterproofing balconies and terraces. It is applied to mineral-based substrates such as concrete, screed, plaster and mortar.
Polymer-Modified, Bitumen-Rubber-Based, Two-Component Waterproofing Material
- Category
- WATERPROOFING MATERIALS
Frequently asked questions
What are the key specifications of IZOBITUM 2K?
The recorded supply specification for IZOBITUM 2K includes Density, g/cm³: 1.35 (± 0.05); Drying Time, h: ~24-36; Packing: A: 24 kg + B: 8 kg (total 32 kg); Consumption, kg/m²: 3-5 kg; Elongation, %: 90. The full table is listed on this page.
How is IZOBITUM 2K packaged and stored?
Packaging: A: 24 kg + B: 8 kg (total 32 kg). Shelf life: 12 months.
Is IZOBITUM 2K KKDİK registered, and which documents are available?
Yes. IZOBITUM 2K supplied by KORKİMYA is KKDİK registered. The SDS and the certificate of analysis (CoA) for the lot you are evaluating are available on request through this page.
Related Products
Last updated: 10/11/2026
MSDS Available on Request · Export Registered · korkimya.com